(844) 742-3862

Hydro Jetting vs Snaking: Which Does Your Line Need?

Snaking opens a path through a clog. Hydro jetting cleans the whole inside of the pipe. Both are legitimate tools, and the cheaper one is often enough. The right choice depends on what is in the line, what the line is made of and how often the clog comes back.

In Salt Lake City, where many homes still drain through clay pipe laid before 1940, that last question matters more than it does in newer suburbs. This guide explains how each tool works and when each one is the right call.

How each one works

Snaking

A drain snake, also called an auger or cable machine, is a coiled steel cable with a cutting head. The plumber feeds it into the line and spins it. The head breaks up or hooks the clog so water can flow again. Larger machines are used for main sewer lines; smaller hand units handle sinks and tubs.

Hydro jetting

A jetter pushes water at high pressure through a hose with a special nozzle. Rear-facing jets pull the hose forward and scour the pipe wall as it goes. Different nozzles cut roots, break up grease or clear scale. Because it cleans the full circumference of the pipe, buildup takes longer to return.

Side by side

QuestionHydro jettingSnaking
What it doesScours the full pipe wall with high-pressure waterPunches or cuts a path through the clog
Best forRoots, grease, scale, repeat clogsA single soft clog
How long it lastsLonger, because the wall is cleanedShorter, because buildup stays on the wall
On old pipeCamera first; pressure can worsen a cracked lineLower risk, but can snag on broken joints

The short version: snaking treats the clog, jetting treats the pipe.

When snaking is enough

  • A single sink, tub or toilet is slow for the first time.
  • The clog is soft: hair, soap or paper near the drain.
  • The line is old, and a camera shows cracked or offset joints that high pressure could make worse.
  • You need the line open today, and a full cleaning can wait for a planned visit.

A good plumber will tell you when a snake is the right tool. If the first visit is a quick snake and the problem never returns, that was the right call. For single-drain problems, see drain cleaning.

When jetting is the better fit

  • Roots grow back into the line every year.
  • Grease has built up on the pipe wall, common in kitchen lines and restaurants.
  • The same clog keeps coming back after snaking.
  • A home inspector needs a clean line to finish a sewer scope.
  • Scale has built up inside older cast iron.

Roots are the most common reason Salt Lake City homeowners end up jetting. In older neighborhoods like the Avenues and Yalecrest, decades-old trees sit over clay laterals. A snake cuts a hole through the roots; jetting clears more of them from the wall. See why roots come back for the longer story.

Why the pipe material matters

Salt Lake City has housing from every era, and the sewer pipe under each house reflects when it was built.

EraCommon lateral materialWhat it means for cleaning
Before about 1950ClayStrong but jointed every few feet. Roots enter at joints. Jetting works well on sound pipe; camera first.
Mid-centuryCast iron, some OrangeburgCast iron scales inside. Orangeburg fiber pipe deforms with age and usually should not be jetted.
Newer homesPVC or ABS plasticSmooth, sealed joints. Clogs are usually grease or objects, not roots.

These are general patterns, not rules. A camera look tells you what is actually under your house. Our old-pipe safety guide covers each material in more detail.

The case for a camera look first

The camera is what turns a guess into a decision. It shows whether the clog is roots, grease, scale or a broken section, and whether the pipe can take high pressure. It also gives you footage you can compare on the next visit.

On a newer plastic line with a known grease problem, skipping the camera can be reasonable. On a 1920s clay line in Sugar House or Liberty Wells, it rarely is. See sewer camera inspections explained.

What each one costs

Snaking is usually cheaper per visit. Angi lists Salt Lake City drain cleaning at an average of $204 and sewer main cleaning at $302, while its national hydro jetting average is $475. Jetting can still be the cheaper choice over a few years if it keeps the line clear longer. Our cost guide has the sources and details.

What each visit looks like

A snaking visit

  1. The plumber finds the nearest access point to the clog, often the drain itself for a sink or tub, or a cleanout for the main line.
  2. They feed the cable in until it meets resistance, then work the head through the clog.
  3. They run water to confirm it drains, and may pull the cable back to show you what came out.
  4. Most single-drain visits are short. A main-line snake takes longer, especially through roots.

A jetting visit

  1. The plumber finds a cleanout or other access point large enough for the jetting hose.
  2. On an older line, they run a camera first to check the pipe and find the problem.
  3. They choose a nozzle and pressure for the pipe and the blockage, then work the hose along the full length of the line.
  4. They flush the line and, ideally, run the camera again so you can see the result.
  5. A jetting visit usually takes longer than snaking because the whole line is cleaned, not just the clog.

Signs the snake did not fix it

  • The same drain slows down again within weeks.
  • Several drains are slow at once, which points to the main line, not one fixture.
  • Toilets gurgle when the washer drains.
  • Water appears at the basement floor drain, especially in spring.

Any of these is a reason to ask for a camera look and talk about jetting. In older Salt Lake City homes, repeat clogs are usually roots or buildup that a snake only cut through. For main-line symptoms, see sewer line cleaning.

Keeping the line clear afterward

Whichever tool you use, a few habits keep the line open longer:

  • Keep grease out of the kitchen sink. Wipe pans and put cooled grease in the trash.
  • Flush only toilet paper. Wipes marketed as flushable still catch on roots and joints.
  • Use drain screens in tubs and showers.
  • If roots are the cause, book the next cleaning before they block the line, often late winter before snowmelt.
  • Keep the camera footage and compare it next time.

Kitchen lines, laundry lines and the main

Where the clog sits changes the answer. A house has several branch lines that join the main sewer line, which then runs under the yard to the city sewer.

  • Bathroom sink or tub. Usually hair and soap close to the drain. A small snake is almost always enough.
  • Kitchen sink. Grease builds up along the whole branch line. Snaking opens it, but jetting is often what keeps it open.
  • Laundry line. Lint and soap can narrow the line over years. Repeated slow draining is a reason to look further.
  • Main sewer line. Roots, grease from the whole house and broken sections. This is where jetting does most of its work in older Salt Lake City homes.

If you are not sure which line is clogged, notice which fixtures are slow. One fixture points to a branch; several at once, or the basement floor drain, points to the main.

Common mistakes

  • Snaking the same line every few months without asking why it keeps clogging.
  • Jetting a cracked or collapsed section without a camera look first.
  • Choosing by price per visit instead of cost over a year or two.
  • Assuming a newer home has no root risk; trees planted with the house can reach the line in a few decades.

Questions to ask the plumber

  1. Which do you recommend for this line, and why?
  2. Can you run a camera first?
  3. If you snake it, what are the odds it clogs again soon?
  4. If you jet it, what pressure and nozzle will you use on this pipe material?
  5. Is the quote in writing, and does it include a camera look after?

The bottom line

Snake a first-time, soft clog. Jet roots, grease and clogs that keep coming back, once a camera shows the pipe can take it. To reach a licensed Salt Lake City plumber who can look at your line, call (844) 742-3862.

Common questions

Is hydro jetting better than snaking?

Not always. Snaking is often enough for a single soft clog. Jetting is better for roots, grease and clogs that keep coming back, because it cleans the whole pipe wall.

Can hydro jetting damage old pipes?

It can make an already cracked or broken section worse. That is why a camera look first is wise on clay, cast iron or Orangeburg lines.

Which is cheaper, jetting or snaking?

Snaking is usually cheaper per visit. Jetting can cost less over time if it keeps the line clear longer.

How do I know which one my line needs?

A camera inspection shows what is causing the clog and what shape the pipe is in. That answer decides the tool.

Sources

Talk to a licensed Salt Lake City plumber

One call connects you. Free referral service; plumbers set their own prices.

Call (844) 742-3862